SHENZHENSHI JUNXIN DIANZI YOUXIANGONGSI

1/2.3-Inch 14Mp CMOS Digital Image Sensor
Features
• DigitalClarity® CMOS imaging technology
• 1.4μm pixel with Aptina™ A-Pix technology
• Simple two-wire serial interface
• Auto black level calibration
• Full HD support at 60fps for maximum video
performance
• 20 percent extra image array area in full HD to enable
digital image stabilization (EIS).
• Support for external mechanical shutter
• Support for external LED or xenon flash
• High frame rate preview mode with arbitrary downsize scaling from maximum resolution
• Programmable controls: gain, horizontal and vertical
blanking, frame size/rate, exposure, left–right and
top–bottom image reversal, window size, and
panning
• Data interfaces: parallel or four-lane serial highspeed pixel interface (HiSPi™) differential signalling
(sub-LVDS)
• On-chip phase-locked loop (PLL) oscillator
• Bayer pattern downsize scaler
• Integrated position-based color and lens shading
correction
Applications
• Digital video cameras
• Digital still cameras
General Description
The Aptina™ MT9F001 is a 1/2.3-inch CMOS activepixel digital imaging sensor with an active pixel array of
4608H x 3288V (4640H x 3320V including border pixels).
It can support 14-megapixel (4384H x 3288V) digital
still images and a 1080p plus additional 20 percent pixels for electronic image stabilization (4608H x 2592V) in
digital video mode. The MT9F001 sensor is programmable through a simple two-wire serial interface, and
has low power consumption.
Optical format 1/2.3-inch (4:3)
Active pixels and imager
size
• 4608H x 3288V: (entire array):
6.451mm (H) x 4.603mm (V), 7.925mm
diagonal
• 4384H x 3288V (4:3, still mode):
6.138mm (H) x 4.603mm (V), 7.672mm
diagonal
• 4608H x 2592V (16:9, video mode):
6.451mm (H) x 3.629mm (V), 7.402mm
diagonal
Pixel size 1.4 x 1.4μm
Chief ray angle 0°
Color filter array RGB Bayer pattern
Shutter type Electronic rolling shutter (ERS) with global
reset release (GRR)
Input clock frequency 6–48 MHz
Maximum
data
rate
Parallel 96 Mp/s at 96 MHz PIXCLK
HiSPi (4-lane) 2.8 Gbps
Frame
rate
Full resolution, 4:3
(4384H x 3288V)
Programmable up to 13 fps for HiSPi I/F, 6
fps for parallel I/F
Preview mode
VGA
• 30 fps with binning
• 60 fps with skip2bin2
1080p mode: • 60 fps using HiSPi interface
2304H x 1296V (1080p +20%EIS)
• 30 fps using parallel interface
2150H x 1208V (1080p +10%EIS)
ADC resolution 12-bit, on-die
Responsivity 0.724 V/lux-sec (550nm)
Dynamic range 65.3dB
SNRMAX 365.5dB
Supply
voltage
I/O Digital 1.7–1.9V (1.8V nominal)
or 2.4–3.1V (2.8V nominal)
Digital 1.7–1.9V (1.8V nominal)
Analog 2.4–3.1V (2.8V nominal)
I/O SLVS 0.3 - 0.9V (0.4 or 0.8V nominal)
Power
Consumption
Full resolution 700mW (HiSPi serial I/F, 12-bit, 13 fps)
Video 550mW (HiSPi serial I/F, 10-bit, 60 fps)
Preview lowpower VGA
280mW (HiSPi serial I/F, 10-bit, 1096H x
822W)
Standby 200μW (typical, EXTCLK disabled)
Package 48-pin iLCC (10mm x 10mm) and bare die
Operating temperature –30°C to +70°C (at junction)